| Author |
Message |
Carlos
Guest
|
 Posted:
Thu Nov 25, 2004 5:57 pm Post subject:
AD822, good TL062 replacement? |
|
|
Just bumped into it looking for quieter alternatives to the ubiquitous
TL062 for a battery powered bass guitar tone circuit. Ok, power
consumption is higher, but still much lower than the usual audio opamp
suspects, noise is decent, THD doesn't look bad. It's expensive but in
opamp world that means it costs $5 instead of $0.50 and I only need
one, so I think I'll manage. Any reason not to use it or any better
alternatives?
Many thanks,
Carlos
|
|
| Back to top |
|
 |
Winfield Hill
Guest
|
| Posted:
Thu Nov 25, 2004 5:57 pm Post subject:
Re: AD822, good TL062 replacement? |
|
|
Carlos wrote...
| Quote: |
Just bumped into it looking for quieter alternatives to the
ubiquitous TL062 for a battery powered bass guitar tone circuit.
Ok, power consumption is higher, but still much lower than the
usual audio opamp suspects, noise is decent, THD doesn't look bad.
It's expensive but in opamp world that means it costs $5 instead
of $0.50 and I only need one, so I think I'll manage. Any reason
not to use it or any better alternatives?
|
The AD822 is a JFET replacement for an LM358 (half of an LM324)
or LT1013 single-supply opamp, featuring rail-to-rail outputs.
Both the single-supply and rail-to-rail aspects are attractive
for some applications (especially with a JFET input), but both
involve compromises that degrade the opamp's performance. There
are _much_ better choices for high-quality audio JFET opamps.
--
Thanks,
- Win |
|
| Back to top |
|
|
Graham Holloway
Guest
|
| Posted:
Thu Nov 25, 2004 5:57 pm Post subject:
Re: AD822, good TL062 replacement? |
|
|
"Winfield Hill" <hill_a@t_rowland-dotties-harvard-dot.s-edu> wrote in
message news:co4v7f0p31@drn.newsguy.com...
| Quote: | Carlos wrote...
Just bumped into it looking for quieter alternatives to the
ubiquitous TL062 for a battery powered bass guitar tone circuit.
Ok, power consumption is higher, but still much lower than the
usual audio opamp suspects, noise is decent, THD doesn't look bad.
It's expensive but in opamp world that means it costs $5 instead
of $0.50 and I only need one, so I think I'll manage. Any reason
not to use it or any better alternatives?
The AD822 is a JFET replacement for an LM358 (half of an LM324)
or LT1013 single-supply opamp, featuring rail-to-rail outputs.
Both the single-supply and rail-to-rail aspects are attractive
for some applications (especially with a JFET input), but both
involve compromises that degrade the opamp's performance. There
are _much_ better choices for high-quality audio JFET opamps.
|
Would you care to let us have your thoughts on high-quality audio op amps?
Graham Holloway
|
|
| Back to top |
|
|
Glenn Gundlach
Guest
|
| Posted:
Thu Nov 25, 2004 10:12 pm Post subject:
Re: AD822, good TL062 replacement? |
|
|
clorenzo@eutelsat.fr (Carlos) wrote in message news:<bdab6169.0411250707.2362c7b7@posting.google.com>...
| Quote: | Just bumped into it looking for quieter alternatives to the ubiquitous
TL062 for a battery powered bass guitar tone circuit. Ok, power
consumption is higher, but still much lower than the usual audio opamp
suspects, noise is decent, THD doesn't look bad. It's expensive but in
opamp world that means it costs $5 instead of $0.50 and I only need
one, so I think I'll manage. Any reason not to use it or any better
alternatives?
Many thanks,
Carlos
|
You might want to check out these chips
http://focus.ti.com/lit/ds/symlink/opa2134.pdf
gg |
|
| Back to top |
|
|
Karl Uppiano
Guest
|
| Posted:
Thu Nov 25, 2004 10:12 pm Post subject:
Re: AD822, good TL062 replacement? |
|
|
"Glenn Gundlach" <stratus46@yahoo.com> wrote in message
news:acb22b57.0411251202.7c610cc@posting.google.com...
| Quote: | clorenzo@eutelsat.fr (Carlos) wrote in message
news:<bdab6169.0411250707.2362c7b7@posting.google.com>...
Just bumped into it looking for quieter alternatives to the ubiquitous
TL062 for a battery powered bass guitar tone circuit. Ok, power
consumption is higher, but still much lower than the usual audio opamp
suspects, noise is decent, THD doesn't look bad. It's expensive but in
opamp world that means it costs $5 instead of $0.50 and I only need
one, so I think I'll manage. Any reason not to use it or any better
alternatives?
Many thanks,
Carlos
You might want to check out these chips
http://focus.ti.com/lit/ds/symlink/opa2134.pdf
gg
|
Looks like the JFET equivalent to the venerable 5534 (performance rated for
driving 600 Ohm loads). Nice choice. |
|
| Back to top |
|
|
Pooh Bear
Guest
|
| Posted:
Fri Nov 26, 2004 2:12 am Post subject:
Re: AD822, good TL062 replacement? |
|
|
Glenn Gundlach wrote:
| Quote: | clorenzo@eutelsat.fr (Carlos) wrote in message news:<bdab6169.0411250707.2362c7b7@posting.google.com>...
Just bumped into it looking for quieter alternatives to the ubiquitous
TL062 for a battery powered bass guitar tone circuit. Ok, power
consumption is higher, but still much lower than the usual audio opamp
suspects, noise is decent, THD doesn't look bad. It's expensive but in
opamp world that means it costs $5 instead of $0.50 and I only need
one, so I think I'll manage. Any reason not to use it or any better
alternatives?
Many thanks,
Carlos
You might want to check out these chips
http://focus.ti.com/lit/ds/symlink/opa2134.pdf
|
Supply current at 4mA / op-amp is somewhat more than a TL062. Not ideal for battery operated.
Graham |
|
| Back to top |
|
|
Carlos
Guest
|
| Posted:
Fri Nov 26, 2004 10:12 am Post subject:
Re: AD822, good TL062 replacement? |
|
|
But are there any with the sort of power consumption of the AD822 (800
uA/amp), preferably in an 8PDIP package? My first choice would have
been the OPA2134 (what I normally use), but as someone else said at 4
mA/amp is on the high side for battery operation.
Many thanks again,
Carlos
Winfield Hill <hill_a@t_rowland-dotties-harvard-dot.s-edu> wrote in message news:<co4v7f0p31@drn.newsguy.com>...
> There are _much_ better choices for high-quality audio JFET opamps. |
|
| Back to top |
|
|
Len Moskowitz
Guest
|
| Posted:
Sat Nov 27, 2004 12:14 am Post subject:
Re: AD822, good TL062 replacement? |
|
|
Carlos <clorenzo@eutelsat.fr> wrote:
| Quote: | Just bumped into it looking for quieter alternatives to the ubiquitous
TL062 for a battery powered bass guitar tone circuit. Ok, power
consumption is higher, but still much lower than the usual audio opamp
suspects, noise is decent, THD doesn't look bad. It's expensive but in
opamp world that means it costs $5 instead of $0.50 and I only need
one, so I think I'll manage. Any reason not to use it or any better
alternatives?
|
If I recall correctly, I used it in my upgrade for a Music Man
StingRay Bass tone circuit.
Here's the article from long ago:
A few weeks back I wrote about how Mabel, my most attractive Ernie Ball
Music Man StingRay, had a bit of noticeable hiss when listened to
through headphones. When played through a speaker bottom the hiss
wasn't noticeable at all, but I sometimes record plugged directly into
the mixing board and often practice with my AMP BH420 head driving my
Grado HP-1 headphones. Then the hiss was a bit much.
Where did Mabel's hiss come from? Well, the StingRay has an active
pre-amp. The key component in the pre-amp is a Motorola TL-082 dual
op-amp. While it works very well on a single 9 Volt battery, has an
admirably low power consumption and a fast slew rate, the TL-082 does
have a fairly high noise level. If I boosted Mabel's high frequency EQ
at all, the hiss started to intrude. Luckily, dual op-amps come in a
standard 8-pin DIP package with standard pin-outs. I removed the
TL-082, installed a high quality socket in its place, and went
spelunking through the IC catalogs for potential replacements. When the
data sheets pointed to a likely candidate I rounded one up, plugged it
in and listened.
It wasn't an easy search but I found just the one: the Analog Devices
AD822. It has much better noise specs with only a negligible reduction
in battery life. And in addition to its lower noise, it brings an
equally important side effect: it sounds better! Considering how much I
already love my Mabel's tone, this is *not* a trivial matter.
When I listen very critically to Mabel using top quality 'phones, the
TL-082 has a quality that I can only characterize as slightly brittle,
or maybe a little glassy, or even like a little bit of momentary
flanging on the attack of a picked note, sort of a
tap-on-a-window-with-a-glass-rod overtone. The only way to tame it is
to cut too much of the StingRay's characteristic clarity and bite with a
serious cut of the amp's high frequency EQ. But when I installed the
AD822, the brittleness disappeared leaving Mabel's clarity and
incredibly forceful low end intact.
Even with the new op-amp, if I boost Mabel's high end a bit too much I
can still hear hiss, but it's not close to the TL-082's intrusive level.
And to keep me interested, her newly tamed voice is even more enticing
than before.
--
Len Moskowitz PDAudio, Binaural Mics, Cables, DPA, M-Audio
Core Sound http://www.stealthmicrophones.com
Teaneck, New Jersey USA http://www.core-sound.com
moskowit@core-sound.com Tel: 201-801-0812, FAX: 201-801-0912 |
|
| Back to top |
|
|
Len Moskowitz
Guest
|
| Posted:
Sat Nov 27, 2004 12:14 am Post subject:
Re: AD822, good TL062 replacement? |
|
|
Karl Uppiano <karl.uppiano@verizon.net> wrote:
| Quote: | Looks like the JFET equivalent to the venerable 5534 (performance rated for
driving 600 Ohm loads). Nice choice.
|
But it's not single supply.
--
Len Moskowitz PDAudio, Binaural Mics, Cables, DPA, M-Audio
Core Sound http://www.stealthmicrophones.com
Teaneck, New Jersey USA http://www.core-sound.com
moskowit@core-sound.com Tel: 201-801-0812, FAX: 201-801-0912 |
|
| Back to top |
|
|
Winfield Hill
Guest
|
| Posted:
Sat Nov 27, 2004 12:14 am Post subject:
Re: AD822, good TL062 replacement? |
|
|
Carlos wrote...
| Quote: |
But are there any with the sort of power consumption of the AD822
(800uA/amp), preferably in an 8PDIP package? My first choice would
have been the OPA2134 (what I normally use), but as someone else
said at 4mA/amp is on the high side for battery operation.
|
I'd say if you want 0.00008% distortion you'll have to pay the 4mA.
Perhaps you can afford more distortion? If so, how much?
--
Thanks,
- Win |
|
| Back to top |
|
|
Dave Platt
Guest
|
| Posted:
Sat Nov 27, 2004 12:14 am Post subject:
Re: AD822, good TL062 replacement? |
|
|
| Quote: | Karl Uppiano <karl.uppiano@verizon.net> wrote:
Looks like the JFET equivalent to the venerable 5534 (performance rated for
driving 600 Ohm loads). Nice choice.
But it's not single supply.
|
In many circuits, this won't matter. If the inputs and outputs of the
op amp are capacitor-coupled, and there's a resistive-divider biasing
network connected between the input and each supply pin, and if the
circuit doesn't require the op amp to drive its output particularly
close to either voltage rail, then it won't matter whether the op amp
is marketed as "single supply" or not.
Since op amps have no ground pin, and really don't know where "ground"
is in relation to their supply voltages, what really matters to them
is how close to their positive and negative rail voltages the input
and output signals have to go.
--
Dave Platt <dplatt@radagast.org> AE6EO
Hosting the Jade Warrior home page: http://www.radagast.org/jade-warrior
I do _not_ wish to receive unsolicited commercial email, and I will
boycott any company which has the gall to send me such ads! |
|
| Back to top |
|
|
Karl Uppiano
Guest
|
| Posted:
Sat Nov 27, 2004 12:14 am Post subject:
Re: AD822, good TL062 replacement? |
|
|
| Quote: | But it's not single supply.
|
Both are -- or not -- you just bias them differently. |
|
| Back to top |
|
|
Pooh Bear
Guest
|
| Posted:
Sat Nov 27, 2004 6:02 am Post subject:
Re: AD822, good TL062 replacement? |
|
|
Len Moskowitz wrote:
| Quote: | Carlos <clorenzo@eutelsat.fr> wrote:
Just bumped into it looking for quieter alternatives to the ubiquitous
TL062 for a battery powered bass guitar tone circuit. Ok, power
consumption is higher, but still much lower than the usual audio opamp
suspects, noise is decent, THD doesn't look bad. It's expensive but in
opamp world that means it costs $5 instead of $0.50 and I only need
one, so I think I'll manage. Any reason not to use it or any better
alternatives?
If I recall correctly, I used it in my upgrade for a Music Man
StingRay Bass tone circuit.
Here's the article from long ago:
A few weeks back I wrote about how Mabel, my most attractive Ernie Ball
Music Man StingRay, had a bit of noticeable hiss when listened to
through headphones. When played through a speaker bottom the hiss
wasn't noticeable at all, but I sometimes record plugged directly into
the mixing board and often practice with my AMP BH420 head driving my
Grado HP-1 headphones. Then the hiss was a bit much.
Where did Mabel's hiss come from? Well, the StingRay has an active
pre-amp. The key component in the pre-amp is a Motorola TL-082 dual
op-amp. While it works very well on a single 9 Volt battery, has an
admirably low power consumption and a fast slew rate, the TL-082 does
have a fairly high noise level. If I boosted Mabel's high frequency EQ
at all, the hiss started to intrude. Luckily, dual op-amps come in a
standard 8-pin DIP package with standard pin-outs. I removed the
TL-082, installed a high quality socket in its place, and went
spelunking through the IC catalogs for potential replacements. When the
data sheets pointed to a likely candidate I rounded one up, plugged it
in and listened.
It wasn't an easy search but I found just the one: the Analog Devices
AD822. It has much better noise specs with only a negligible reduction
in battery life. And in addition to its lower noise, it brings an
equally important side effect: it sounds better! Considering how much I
already love my Mabel's tone, this is *not* a trivial matter.
When I listen very critically to Mabel using top quality 'phones, the
TL-082 has a quality that I can only characterize as slightly brittle,
or maybe a little glassy, or even like a little bit of momentary
flanging on the attack of a picked note, sort of a
tap-on-a-window-with-a-glass-rod overtone. The only way to tame it is
to cut too much of the StingRay's characteristic clarity and bite with a
serious cut of the amp's high frequency EQ. But when I installed the
AD822, the brittleness disappeared leaving Mabel's clarity and
incredibly forceful low end intact.
Even with the new op-amp, if I boost Mabel's high end a bit too much I
can still hear hiss, but it's not close to the TL-082's intrusive level.
And to keep me interested, her newly tamed voice is even more enticing
than before.
|
It was daft to use the TL082 in the first place.
The TL072 has the same current draw IIRC but lower noise. It is widely used
in quality audio ( whereas the 082 isn't ).
The TL062 has a tiny current draw ( great for battery use ) but is noiser
than the 082. Horses for courses.
Graham |
|
| Back to top |
|
|
Carlos
Guest
|
| Posted:
Sat Nov 27, 2004 6:13 am Post subject:
Re: AD822, good TL062 replacement? |
|
|
Winfield Hill <hill_a@t_rowland-dotties-harvard-dot.s-edu> wrote in message news:<co805202lsl@drn.newsguy.com>...
| Quote: | I'd say if you want 0.00008% distortion you'll have to pay the 4mA.
Perhaps you can afford more distortion? If so, how much?
|
To be honest I think for this application something like 0.1% would be
more than adequate. The circuit is basically a unity gain input buffer
followed by the usual negative feedback tone control arragement with
+/- 20 dB boost/cut, so I'd say worst case would be G = 10 @ 5 kHz
(harmonics and all I don't expect much life above that freq, if any
the 15" speaker will filter it out anyway). Any candidates giving 0.1%
THD or better under those conditions plus better noise performance
than the TL062?
If not, what's the best I can do at or below 1mA/amp consumption?
Tnx+,
Carlos |
|
| Back to top |
|
|
Pooh Bear
Guest
|
| Posted:
Sat Nov 27, 2004 6:13 am Post subject:
Re: AD822, good TL062 replacement? |
|
|
Carlos wrote:
| Quote: | Winfield Hill <hill_a@t_rowland-dotties-harvard-dot.s-edu> wrote in message news:<co805202lsl@drn.newsguy.com>...
I'd say if you want 0.00008% distortion you'll have to pay the 4mA.
Perhaps you can afford more distortion? If so, how much?
To be honest I think for this application something like 0.1% would be
more than adequate. The circuit is basically a unity gain input buffer
followed by the usual negative feedback tone control arragement with
+/- 20 dB boost/cut, so I'd say worst case would be G = 10 @ 5 kHz
(harmonics and all I don't expect much life above that freq, if any
the 15" speaker will filter it out anyway). Any candidates giving 0.1%
THD or better under those conditions plus better noise performance
than the TL062?
If not, what's the best I can do at or below 1mA/amp consumption?
|
The TL072 @ 1.4mA typ per amp Icc is way the best bet IMHO.
It should be a straight drop-in replacement for an 062 too without any further thought.
Not a 'touchy' op-amp ( except as a voltage follower - use a series resistor on the output for driving long lines -
use ~ 100 ohms ) well regarded - characterised low THD and low noise for your application ! Note for Hi-Z pickups,
the source Z may predominate in noise analysis rather than the input noise of the active stage.
Graham |
|
| Back to top |
|
|
|
|
|
|
Profile
Log in to check your private messages
Log in